SEWOO LK-T210 Uživatelský manuál

LK-T21 Thermal Receipt Printer Technical Manual SEWOO TECH CO., LTD. www.miniprinter.com

LK-T21 Technical Manual 1.7 Printing and Cutting Positions Center of the print dotlineAuto-cutter blade positionManual-cutter position[Un

LK-T21 Technical Manual 1.8 Internal Buffer 1) Receive buffer: 4kbyte 1.9 Electrical Characteristics 1) Supply voltage: +24 VDC ± 7% 2)

LK-T21 Technical Manual 2. Configuration 2.1 Interface 2.1.1 RS-232 serial interface 2.1.2 Specifications Data transmission: Serial Sync

LK-T21 Technical Manual 2.1.5 Serial interface connection example Host side Printer side TXD ………………………………… RXD DSR ………………………………… DTR RXD …………

LK-T21 Technical Manual 2.1.6 Centronics parallel interface 1) Specifications Data transmission: 8-bit parallel Synchronization: STROBE pulse sup

LK-T21 Technical Manual 2.1.7 Data Receiving Timing (Compatibility Mode) Specifications Characteristics Symbol Min [ns] Max [ns] Data Hold Time (

LK-T21 Technical Manual 2.1.9 Interface Connector 16

LK-T21 Technical Manual 3. Connectors 3.1 Interface Connectors Refer to Section 2.1, Interface 3.2 Electrical Characteristics 1) Input

LK-T21 Technical Manual CAUTION: To avoid an overcurrent, the resistance of the drawer kick-out solenoid must be 24 Ω or more. Output waveform:

LK-T21 Technical Manual 4 Controle Command summary No. Command Function 1 HT Horizontal tab 2 LF Print and line feed 3 CR Print and c

LK-T21 Technical Manual TABLE OF CONTENTS 1. General Specifications 1.1 Printing Specifications 1.2 Character Specifications 1.3 Auto Cutter 1.

LK-T21 Technical Manual 51 GS I Transmit printer ID 52 GS L Set left margin 53 GS P Set horizontal and vertical motion units 54 GS V

LK-T21 Technical Manual Command Descriptions Command Notation [Name] The name of the control command. [Format] The code sequence.

LK-T21 Technical Manual LF [Name] Print and line feed [Format] ASCII LF Hex 0A Decimal 10 [Description] ·Prints the data in the p

LK-T21 Technical Manual CAN [Name] Cancel print data in page mode [Format] ASCII CAN Hex 18 Decimal 24 [Description] In page mode,

LK-T21 Technical Manual command that consists of 2 or more bytes. Example : If you attempt to transmit ESC 3 n to the printer, but DTR (DSR

LK-T21 Technical Manual temperature drops sufficiently or when the paper roll cover is open during printing, bit 6 is On. n = 4: Continuous paper s

LK-T21 Technical Manual DLE DC4 n m t [Name] Generate pulse at real-time [Format] ASCII DLE DC4 n m t Hex 10 14 n m t

LK-T21 Technical Manual ESC SP n [Name] Set right-side character spacing [Format] ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n [Range]

LK-T21 Technical Manual ESC ! n [Name] Select print mode(s) [Format] ASCII ESC ! n Hex 1B 21 n Decimal 27 33 n [Range] 0≤n ≤

LK-T21 Technical Manual ESC $ nL nH [Name] Set absolute print position [Format] ASCII ESC $ nL nH Hex 1B 24 nL nH Decimal 27 36 nL nH

LK-T21 Technical Manual 1. General Specifications 1.1 Printing Specifications 1) Printing method: Thermal line printing 2) Dot density

LK-T21 Technical Manual ESC & y c1 c2 [x1 d1…d(y x x1)]..[ xk d1..d(y x xk)] [Name] Define user-defined characters [Format] ASCII ESC

LK-T21 Technical Manual 31

LK-T21 Technical Manual ESC ＊m nL nH [d1...dk] 32

LK-T21 Technical Manual [Name] Select bit-image mode [Format] ASCII ESC ＊ m nL nH d1...dk Hex 1B 2A m nL nH d1...dk Decimal

LK-T21 Technical Manual [Name] Turn underline mode on/off [Format] ASCII ESC - n Hex 1B 2D n Decimal 27 45 n [Range] 0≤n ≤2, 48

LK-T21 Technical Manual [Name] Set line spacing [Format] ASCII ESC 3 n Hex 1B 33 n Decimal 27 51 n [Range] 0≤n ≤255 [Description]

LK-T21 Technical Manual [Name] Cancel user-defined characters [Format] ASCII ESC ? n Hex 1B 3F n Decimal 27 63 n [Range] 32 ≤n ≤12

LK-T21 Technical Manual [Name] Set horizontal tab positions [Format] ASCII ESC D n1……nk NUL Hex 1B 44 n1……nk 00

LK-T21 Technical Manual [Name] Turn emphasized mode on/off [Format] ASCII ESC E n Hex 1B 45 n Decimal 27 69 n [Range] 0≤n ≤255 [D

LK-T21 Technical Manual [Name] Print and feed paper [Format] ASCII ESC J n Hex 1B 4A n Decimal 27 74 n [Range] 0≤n ≤255 [Descript

LK-T21 Technical Manual 1) Number of characters: Alphanumeric characters: 95 Extended graphics 128 × 7 pages (including one space page)

LK-T21 Technical Manual [Name] Select page mode [Format] ASCII ESC L Hex 1B 4C Decimal 27 76 [Description] Switches from standard mod

LK-T21 Technical Manual [Name] Select character font [Format] ASCII ESC M n Hex 1B 4D n Decimal 27 77 n [Range] n= 0, 1 , 48, 49

LK-T21 Technical Manual ESC S [Name] Select standard mode [Format] ASCII ESC S Hex 1B 53 Decimal 27 83 [Description] Switches fr

LK-T21 Technical Manual ESC T n [Name] Select print direction in page mode [Format] ASCII ESC T n Hex 1B 54 n Decimal 27 84 n

LK-T21 Technical Manual ESC V n [Name] Turn 90° clockwise rotation mode on/off [Format] ASCII ESC V n Hex 1B 56 n Decimal 27 86 n [Ra

LK-T21 Technical Manual ESC W xL xH yL yH dxL dxH dyL dyH [Name] Set printing area in page mode [Format] ASCII ESC W xL xH yL yH dxL dxH

LK-T21 Technical Manual ·This printable area for this printer is approximately 72.2 mm {512/180”} in the horizontal direction and approximately

LK-T21 Technical Manual ESC a n [Name] Select justification [Format] ASCII ESC a n Hex 1B 61 n Decimal 27 97 n [Range] 0≤n ≤2,48

LK-T21 Technical Manual [Name] Select paper sensor(s) to output paper end signals [Format] ASCII ESC c 3 n Hex 1B 63 33 n Decimal

LK-T21 Technical Manual [Name] Select paper sensor(s) to stop printing [Format] ASCII ESC c 4 n Hex 1B 63 34 n Decimal 27 99 52 n [

LK-T21 Technical Manual 2) Near-end sensor: a) Detection method: Photo Reflector b) Paper roll spool diameter: Inside:

LK-T21 Technical Manual [Name] Print and feed n lines [Format] ASCII ESC d n Hex 1B 64 n Decimal 27 100 n [Range] 0≤n ≤255 [Descr

LK-T21 Technical Manual [Name] Select character code table [Format] ASCII ESC t n Hex 1B 74 n Decimal 27 116 n [Range] 0≤n≤5, 16≤n

LK-T21 Technical Manual [Name] Turns on/off upside-down printing mode [Format] ASCII ESC { n Hex 1B 7B

LK-T21 Technical Manual [Name] Print NV bit image [Format] ASCII FS p n m Hex 1C 70 n

LK-T21 Technical Manual ·If the downloaded bit-image to be printed exceeds one line, the excess data is not printed.

LK-T21 Technical Manual the execution of this command. ·NV bit image means a bit image which is defined in a non-volatile memory by FS q and prin

LK-T21 Technical Manual during processing of the command even when ASB is specified. ·When this command is received during macro definition, the pr

LK-T21 Technical Manual GS ! n [Name] Select character size [Format] ASCII GS ! n Hex 1D 21 n

LK-T21 Technical Manual GS $ nL nH [Name] Set absolute vertical print position in page made [Format] ASCII GS $ nL nH

LK-T21 Technical Manual GS ∗ x y d1...d (x × y × 8) [Name] Define downloaded bit image [Format] ASCII GS ∗ x y d1 …

LK-T21 Technical Manual <EPSON Emulation> 6.8mm0.141mm<82.5mm {3.25"} paper width model>82±0.5mm3mm512 dots72.2mm(dot #1-#512)

LK-T21 Technical Manual GS / m [Name] Print down-loaded bit image [Format] ASCII GS / m Hex

LK-T21 Technical Manual GS : [Name] Start/end macro definition [Format] ASCII GS : Hex 1D 3

LK-T21 Technical Manual GS H n [Name] Select printing position of HRI characters [Format] ASCII GS H n Hex 1D

LK-T21 Technical Manual GS L nL nH [Name] Set left margin [Format] ASCII GS L nL nH Hex 1D 4C

LK-T21 Technical Manual GS P x y [Name] Set horizontal and vertical motion units [Format] ASCII GS P x y Hex

LK-T21 Technical Manual GS V ① m GS V ② m n [Name] Select cut mode and cut paper [Format] ASCII ① GS V m Hex

LK-T21 Technical Manual GS W nL nH [Name] Set printing area width [Format] ASCII GS W nL nH Hex 1D

LK-T21 Technical Manual If the printing area width cannot be extended sufficiently, the right space is③ reduced. ·If the width set for the pri

LK-T21 Technical Manual vertical motion unit (y) is used. ② When the starting position is set to the upper right or lower left of the printing ar

LK-T21 Technical Manual GS a n [Name] Enable/Disable Automatic Status Back (ASB) [Format] ASCII GS a n Hex 1D 61

59.5±0.5mm<60mm {2.36"} paper width model>0.141mm3mm2.4mm384 dots54.1mm(dot #1-#384) LK-T21 Technical Manual 57.5±0.5mm0.141mm3mm3.7m

LK-T21 Technical Manual Second byte (printer information) Bit Off / On Hex Decimal Status for ASB 0 - - - Undefined. 1 - - - Undefined. 2

LK-T21 Technical Manual GS f n [Name] Select font for Human Readable Interpretation (HRI)characters [Format] ASCII GS f n

LK-T21 Technical Manual GS k m d1…dk NUL GS k m n d1…dn①② [Name] Print bar code [Format] ASCII GS k ① m d1…dk

LK-T21 Technical Manual data as normal data. ·If the horizontal size exceeds printing area, the printer only feeds the paper. ·This command feeds a

LK-T21 Technical Manual [Example] Printing GS k 72 7 67 111 100 101 13 57 51 When CODE 128 (m = 73) is used: ·Refer to Appendix J fo

LK-T21 Technical Manual ·HRI characters for the control character (<00>H to <1F>H and <7F>H)are space. <Others> Be

LK-T21 Technical Manual Drawer kick-out connector status ( n = 2, 50): Bit Off / On Hex Decimal Function Off 00 0 Drawer kick-out connector

LK-T21 Technical Manual width, the printing area is extended to the minimum width only on the line in question. The minimum width means 1 dot in

LK-T21 Technical Manual ESC i [Name] Execute paper full cut. [Format] ASCII ESC i Hex 1B 69

LK-T21 Technical Manual <STAR Emulation default setting> 57.5±0.5mm<58mm {2.28"} paper width model>0.125mm2.65mm420 dots2.35mm52

LK-T21 Technical Manual Figure 1.6.3 Printable Area for STAR Emulation (When the Paper Width Is Changed) NOTE : The numeric values used